October 6, 2020 By admin 0

IC HT12E DATASHEET PDF

HT12E is a series encoder IC (Integrated Circuit) for remote control applications. It is commonly used for radio frequency (RF) applications. By using the. HT12E Datasheet, HT12E Holtek Encoder Datasheet, buy HT12E Encoder IC. The capa- bility to select a TE trigger on the HT12E or a. DATA trigger on the HT12A/B/C further en- hances the application flexibility of the 2.

Author: Brakinos Voran
Country: Finland
Language: English (Spanish)
Genre: Literature
Published (Last): 5 November 2018
Pages: 22
PDF File Size: 13.66 Mb
ePub File Size: 17.9 Mb
ISBN: 992-3-88962-864-8
Downloads: 34137
Price: Free* [*Free Regsitration Required]
Uploader: Jular

The IC is has a wide range of operating voltage from 2.

HT12E has a transmission enable pin which is active low. For decoding a data the IC will requires an oscillator, luckily this IC has one in-built.

What is Web Browser. Choosing Battery for Robots.

HT12E begins a 4-word transmission cycle upon receipt of a transmission enable. Can range from 2. Transmission enable; active low. Connected to the Ground of htt12e. It is mainly used in interfacing RF and infrared circuits. The Encoded 12 bit output data can be obtained from this pin. Pull the Transmission Enable pin pin 14 to ground to activate transmission. Skip to main content.

Choosing Motor For Robots. It encodes the 12 bit parallel data into serial for transmission through an RF transmitter.

HT12E Encoder IC Pin Diagram, Uses, Equivalents & Datasheet

In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. Submitted by admin on 30 October Arduino based GPS receiver. These two ICs together form an Encoder and Decoder pair. As soon as TE returns to high, the encoder output completes its final cycle and then stops.

  APVAT ACT 2005 PDF

The primary function of HT12E is to encode a bit and send it out through the output pin. The encoded bit can be obtained from the Dout pin pin The 4-bit data that has to be sent has to be given vatasheet the pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7.

They are paired with 2 datashet series of decoders for use in remote control system applications. Interface SD Card with Arduino. This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR.

This cycle is repeated as long as TE is kept low. These four pins datashet used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits. If you want security you can connect any of the 8 pins to 5V to make it high.

HT12E Encoder IC

Interface GPS with Arduino. A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. Simply put, HT12E converts the parallel inputs into serial output. They can also be connected to switches to manually send and receive data. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

  COMPLICATED BY ZANNIE ADAMS PDF

TL — Programmable Reference Voltage. We should set the bits in same pattern on Encoder and Decoder IC to pair them. Supply voltage; 5V 2. In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes dattasheet these 4-bits and they will be reflected on the output side of the HT12D decoder IC.

These 12 bits are divided into 8 address bits and datasheft data bits.

Virgin Galactic — Commercial Space Flight. This high-density System-in-Package SiP integrates controller, power switches, and support components. You can know to set up the HT12D after this from here.

This oscillator can be used by connecting these two pins through a 1M Resistor. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. SPI Module of Arduino. These are the 8-bit address bits, which is used to protect your data. HT12E is an encoder integrated circuit of 2 12 series of encoders. It ix very important that your Decoder should also have this same address for them to talk to each other.

This pin has to be connected to Ground 0V to enable the Transmission.